Is there a way to Reset BIOS password or Response code for Toshiba Qosmio F25 0. Status Solved Priority. Has cyber security been a challenge in your government.
Press the F2 key. The BIOS / CMOS Setup screen should appear. Follow these steps to de-register the password: 1.
Press 'P' to jump to the Password field. 'Registered' will be highlighted. Press the spacebar to change 'Password= Registered' to 'Password= '. Press the spacebar and press Enter.
The BIOS should respond with 'New Password = '. Press Enter again. The BIOS should respond with 'Verify Password= '. Press Enter again. The BIOS should respond with 'Password= Not Registered'.
Press the End key. The BIOS should respond with 'Are You Sure?'
The computer will restart, and load Windows, without requesting a password. Your Laptop was unlocked Thanks for used my service, looking forward to serving you again.
Follow this procedure to delete a BIOS password using the Response Code method. Be sure to keep the computer powered-on during this entire procedure. The Challenge Code issued by the BIOS is only valid until the computer is turned off and back on. At the BIOS password prompt ('PASSWORD = '), press and release the following keys, one after another: Ctrl, Tab, Ctrl, Enter The computer's response should be: PC Serial No.= XXXXXXXXX Challenge Code=XXXXX XXXXX XXXXX XXXXX XXXXX Response Code= 2. Get response code from My Skype: haisung4344 CHALLENGE CODE SCREEN. Press the F1 or F2 key.
The BIOS / CMOS Setup screen should appear. Follow these steps to de-register the password: 1. Press 'P' to jump to the Password field.
'Registered' will be highlighted. Press the spacebar to change 'Password= Registered' to 'Password= '. Press the spacebar and press Enter. The BIOS should respond with 'New Password = '. Press Enter again. The BIOS should respond with 'Verify Password= '. Press Enter again.
The BIOS should respond with 'Password= Not Registered'. Press the End key.
The BIOS should respond with 'Are You Sure?' The computer will restart, and load Windows, without requesting a password. Your Laptop was unlocked Thanks for used my service i love all everybody.
DTC P0633: Theft Deterrent Key Not Programmed When learning the pre-release password, as well as the challenge and response sequence, the engine control module (ECM) is placed in learn mode. DTC P0633 will set automatically as an indicator that the system is in learn mode and not as a fault indicator. Once the password and challenge/response are learned, learn mode will be exited when the engine is successfully started. At this point, the DTC will be cleared. If the ECM does not exit learn mode, P0633 will remain current and indicate a fault. Robocode robot download games.
The 'key' referenced in the DTC descriptor does not refer to the vehicle key. In this case, 'key' is referring to the challenge response.
DTC P0633 requires a successful engine start to exit the learn procedure and clear the DTC. If an unrelated malfunction exists that causes engine starting to be disabled or otherwise unavailable, learn mode will not exit and DTC P0633 will remain current. In this situation, the cause of the inoperative engine starting must be corrected before diagnosing DTC P0633. DTC P1629: Theft Deterrent Fuel Enable Signal Not Received The theft deterrent module (TDM) sends the pre-release password to the engine control module (ECM) via the serial data circuit. The ECM then sends a challenge to the TDM. Both the ECM and TDM perform a calculation on this challenge. If the calculated response from the TDM equals the calculation performed by the ECM, the ECM will allow vehicle starting.
DTC P1629 is an indicator that the challenge response was not received within the required 2 second window. This does not necessarily indicate a fault is present with the TDM or ECM. Factors such as a long engine crank, a delay in the serial data communication, or B-codes set in the TDM will cause DTC P1629 to set. This DTC should not be used as a fault indicator, but rather as a symptom to assist in the diagnosis of these other systems.